The Ultimate Well Water System Maintenance Checklist

Ensure pure, clean Well Water with our Ultimate Maintenance Checklist. Expert tips for a reliable Well Water System. Your guide to water quality assurance!

Well-water systems are the lifeline of homes and businesses. They provide essential water for drinking, cooking, bathing, and other purposes. If you have a well that provides enough pressure but is not working correctly, there are several factors to consider before taking action.

Well tanks

The thriving tank is a critical part of your water supply system. It's where all of your clean, filtered water comes from. It must be maintained to ensure that the system keeps working properly.

  • Check the pressure switch and gauge for proper operation. 
  • For you to have a reliable well pump, there needs to be enough pressure being sent down by the pump so that it can operate correctly (if there isn't enough pressure, then there may also be problems with some other components, such as a bad switch or worn-out bearings). 
  • A good rule of thumb is that filling up all four tires on your car at once would require about 10 gallons. This amount should go into one-gallon increments until it reaches 100 PSI (pounds per square inch). 
  • If any tire has less than 10 gallons but none have more than 100 PSI, check again or replace both tires immediately!

If everything is okay, the next step would be checking out those pesky leaks.

Pressure tanks

The pressure tank is a vital component of your well water system. It stores excess pressure that builds up in the line between your home and the mains and allows you to turn off your faucet when there's too much for you to handle.

Pressure tanks are made from durable plastic or metal, so they can be easily repaired if something goes wrong—you won't need any special tools or skills! In this section we'll go over:

  • How a pressure tank works
  • How to maintain a pressure tank
  • Troubleshooting common problems with pressure tanks

Pressure switch

A pressure switch is a vital part of your sound system. It controls the flow of water through a well pump, which pumps up to 200 gallons per minute (GPM). Pressure switches are essential. They help protect against potential damage from extreme temperatures and can cause problems if they fail.

Pressure switches control how much water is pumped out of your well. It's essential to check them regularly for signs of something wrong. Pressure switches can fail in as little as six months, so test yours every six months.

Gauges and valves

Gauges and valves are used to monitor the water level in your well and control its flow. The gauges can be analog or digital, but either type is necessary to track your system's health. A valve is also essential because it controls how much water flows through your system at any given time.

If you need help determining what kind of valve would work best for your situation, consider whether you want to open and close it manually. An automated version will help keep things running smoothly while ensuring there won't be any hiccups regarding maintenance checks.

Booster pumps

A booster pump is a small, battery-powered device that provides extra pressure to your well water system. It has two functions:

  • It forces water from the surface to deeper levels in the well. It helps prevent waste of valuable resources (like water) by preventing backflow when you’re not using your tap or faucet.
  • It can also be used as an emergency backup when your house has no electricity or power supply. Installing a booster pump is simple once you identify the replacement parts, leading to significant monthly bill savings.

Iron filters

Iron filters are a type of water filter that removes iron from your water. It is one of the most common minerals found in groundwater, so drawing it can help prevent rust stains and scale build-up on faucets, pipes, and appliances.

To determine whether you need an iron filter:

  • If you have well water but no source of city water or plan to use an existing well as your primary source of drinking water.
  • If there is a lot of red clay in your area (which can cause discoloration).

Sediment filters

Sediment filters are devices that remove sediment from water. They are generally installed in the water line after the pressure tank and before it enters your home through a faucet or other opening.

Sediment filters can be made of various materials, including sand, anthracite, and charcoal. The most common type of sediment filter is made from anthracite coal dust; this filter traps particles as small as 0.0001 inches in diameter (1 mm).

Well pump and submersible pump

Well, pumps are usually located in the basement or garage but can also be found on an exterior wall or at the edge of your property. The best way to check for leaks is through a pressure switch (or "tank," as it is often called). This device is connected between the well's pressure tank and pump. It will immediately alert you to any issues with either component. Turn off all power sources from both sides to ensure this works correctly. These include fuses and circuit breakers.

Ensure the Well Water System is Working Optimally.

Well, water is an integral part of your home's infrastructure. It supplies you with clean, fresh water for drinking, cooking, and cleaning, especially during summer heat. As a homeowner, it is your responsibility to maintain and repair your well as necessary so that you do not suffer from any loss of service or pollution of your well and water supply. Moreover, proper maintenance will ensure that your system operates properly and efficiently, minimizing the risk of unnecessary repairs, which can be pretty costly. Well-water systems can be expensive and dangerous if not maintained properly. Well-water systems cause health problems, property damage, and even death in some cases. For professional water system repair and maintenance, don't hesitate to reach out to experts who can help safeguard your water supply and ensure the longevity of your thriving system.


Clint Hero

8 Blog posts

Comments